HOLDEN 308 H276 218/218 472/472-110
Hydraulic Camshaft H-276 (1800-4800 RPM Range) Suit Holden 235-308 1970-88
Duration advertised Inlet 280°, Exh 280°
Duration advertised @ .050" Inlet 218°, Exh 218°
Valve lift with 1.6 rocker Inlet .472", Exh .472"
Lobe separation angle 110°
HOLDEN 308 MECH CC288 252/260 572/591-108
Solid Camshaft CC288 (3800-7500 RPM Range) Suit Holden 235-308
FORD 351C F238 238/248 554/577 108
F-238 Solid Camshaft Ford 302-351C 238/248 @.050", .554/.577" Lift, 108 LSA
FORD 351C F246 246/256 570/590 108
F-246 Solid Camshaft Ford 302-351C 246/256 @.050", .570/.590" Lift, 108 LSA
FORD 351C F260 260/260 639/639 106
Solid Camshaft F-260 (4200-7600 RPM Range) Suit Ford 302-351C
HOLDEN VN MECH 244/248 553/562-109
F-280 Solid Camshaft Holden 5.0L EFI 244/248 @.050", .553/.562" Lift, 109 LSA
HOLDEN VN MECH 252/260 572/591-108
Solid Camshaft F-288 (4000-7500 RPM Range) Suit Holden 5.0L EFI
HOLDEN V8 VN-VS CCH268 HYD CAM
Hydraulic Camshaft H-268 (1500-4000 RPM Range) Suit Holden 5.0L EFI
HOLDEN 308 H286 230/230 496/496 -110
Hydraulic Camshaft H-286 (2200-6000 RPM Range) Suit Holden 235-308
HOLDEN 308 H304 236/236 520/520 -110
Hydraulic Camshaft H-304 (3000-6500 RPM Range) Suit Holden 235-308
HOLDEN V8 VN-VS CCH276 HYD CAM
Hydraulic Camshaft H-276 (1800-4500 RPM Range) Suit Holden 5.0L EFI
HOLDEN V8 VN-VS CCH286 HYD CAM
Hydraulic Camshaft H-286 (2500-6000 RPM Range) Suit Holden 5.0L EFI
PS20 XR700/XR3000 IGNITION COIL
PS20 Ignition Coil
Great as a high output replacement for OE electronic ignition and points applications on vehicles that require a conventional round coil.
Designed for use with Crane XR700 ignitions.
For general purpose use in applications when engine RPM does not exceed 6500 RPM.
Includes ballast resistor for points applications.
Black finish.
Fits most OE brackets.
CHEV FUEL PUMP PUSHRODS CAST CAM
Fuel Pump Pushrod Suit Chev V8
crane's Heat Treated Tubular Steel Fuel Pump Pushrods For Chevro let's Popular Small Block And Big Block V8 Engines Are Centreless Ground For Concentricity And Are Also Much Lighter Than Oe Type Pushrods, While Main taining The Strength And Stiff ness Required For Reliability In Severe Usage Applications.< br>
part No. 11985-1 Is Specifically For Use With 8620 St eel Billet Roller Camshafts. One End Of The Push Rod Has A Bronze Tip To Compatibly Bear Against The Fuel Pump Eccentric On The Camshaft, Eliminating The Wear Problems That Occur W hen Using A Standard Fuel Pump Pushrod (especially In Endurance Type Applications.
part No. 11986-1 Is For Hydraulic And Mechanical Cast Type Camshafts. Both Ends Of This Pushrod Are Steel Tipped For Best Wear Characteristics.
chev F/pump P/rod Cast Billet Cam
LASH CAPS 5/16 .060
Lash Caps Set 5/16" (Set of 16)
precision Mac hined From 8620 Steel Alloy, H eat Treated And Black Oxided, These High Quality Valve Lash Caps Are A Must In Severe Usag e Applications To Provide A Be tter Wear Surface, And To Leng then The Valve For Correct Geo metry.
lash Caps 5/16" Dia.valve Stems 16 Pk. < br>
32 ROCKER SHIM FORD 351C/LS1
ROCKER PEDESTAL SHIM KIT,FO RD X-FLOW 6, 302-351C & 429-460
Rocker Arm Pedestal Shim Kit
crane's Rocker Arm Pedestal Shim Kit Is For Use On Ford Engines Utilising Non-adjust able Pedestal Mounted Rocker A rms. Reduce The Preload By Approximately .030", .060", .090" .
these Will Fit The Ford 255-302, 351w, 351c, 351m, 400 ,370, 429 And 460 Engines.
rocker Arm Pedestal Shim K it (32).
32 ROCKER SHIMS AMC/OLDS/308
ROCKER BRIDGE SHIM KIT,HOLDEN ALSO SUITS OLDSMOBI LE/PONTIAC
Rocker Arm Bridge Shim Kit
crane's Rocker Arm Bridge Shim Kit Will Correct For Excessive Hydraulic Lifter Pre-load On Late Model Engines. Two Different Thickness Shims Are Included To Decrease Lifter Pre load By Approximately .030", . 060" Or .090" These Shims Can Be A Quick And Easy Alternative To Resorting To Different Length Pushrods.
rocker Arm Pedestal Shim Kit (32).
HOLD V8 ALL ULTRA PRO LIFTERS
Solid Roller Lifter Set (.842" dia.) Suit Holden V8
Endure-x Solid Roller Lifters Are Fully Heat-treated, Machin ed To Ultra-high Tolerances An d Fully Rebuildable.
a ll Models Feature Edm Oil Inje ction Technology, Which Ensure s That The Roller Bearing Asse mbly Receives A Constant Flow Of Pressurized Oil. This Virtu ally Eliminates Needle Bearing Oil Starvation, Historically A "problem Area" For All Solid Roller Lifters When Used In L ow Rpm And Street Applications .
comp Cams Super Roll er Lifters Are Available For A Variety Of Applications, Incl uding Small Base Circle Camsha ft And Offset Pushrod Seat Con figurations.
endure-x Solid Roller Lifter Features < br>
1. Patented Link Bar As sembly Combines The Benefits O f A Removable Link Bar With Th e Safety Of A Captured Link Ba r.
2. Edm Oil Injectio n Guarantees That The Bearing Assembly Receives A Constant F low Of Pressurized Oil Via A P recision Hole Aimed Directly A t The Needle Bearings.
3. Precision Sorted Bearings -distribute Loads Evenly, Prev enting Premature Wear And Fail ure.
4. Tool Steel Axl e -prolongs The Life Of The Ro ller Assembly, Particularly In High Rpm Applications.
special Note: Solid Roller Li fters Are Designed For Use In Racing Applications; However I f Used In Street Applications Precautions Should Be Taken To Avoid Excessive Idling And Ce rtain Engine Builder Modificat ions Are Required. Low Rpm Usa ge May Result In A Lack Of Lub rication From Windage, Prematu re Wear And Ultimately Extensi ve Engine Damage.
GROUP A 1.65 7/16 ROLLER ROCKER
Aluminium Roller Rocker Set 1.65 Ratio 7/16" Suit Holden 253-308, Pontiac/AMC
CHEV/308 .491 BRONZE DIST GEAR
Bronze Distributor Gear .491" Suit S/B Chev
Dist. Bronze Drive Gears
made From High Silicon Copper Alloy And Precision Machined . A Necessity When Using A 862 0 Steel Billet Camshaft.
< br>chev V8 262-400, 396-502, V 6 90deg 200-262
for Standard Oe Distributor With .490 " Shaft Diam. Also Fits Accel 34000, 35000 And 41000 Series< br>
DUAL SPRING 130@1.850 338@1.30'
Dual Valve Spring Set 1.46" O.D 120lbs. @ 1.875" with 1.08" Coil Bind
XR 700 LUCAS OPTO 4-6-8/V12 JAG
XR700 Ignition Conversion Kit Suit Lucas 4, 6, 8 & 12
Xr700 Points-to-electronic Ignition Conversion Kits
the Fireball Xr700 Is Designed For Replacement Of Breaker Points And Failed Oe Modules In Street Driven Vehicles. Xr700 U nits Are Compatible With The Original Coil And Ballast Resistor. Because There Are No Contact Points Or Rubbing Block To Wear Out, You Set The Engine Timing Once.
xr700 - Lucas 4,6,8,12 Cyl.